Ads code here

IKEA Hack Co-Sleeping Bed

Do not forget! follow DIYSelfy on facebook to get new and fresh ideas and updates everyday!

Now this is a fun idea. It’s a bed that sleeps seven. Do your kids always want to climb in bed with you? It can make for a very cramped sleeping space. One family, the Boyces, came up with a creative solution to this problem. Who knew what you could do with two Ikea beds and some ingenuity? We hope this Ikea Hack Kura Bed tutorial makes it even easier for your family to get the sleep you need!!


Under is a drawing that best represents this new bed and will visually allow you to see how simple it really is!  Your bed size will vary depending on your space. 


Step 1:  Purchase two IKEA Kura Beds

Expect to pay between $75-$125 used and $200 new per bed.  IKEA sells a thinner mattress that would make the rails higher but you can use your own mattresses.  You can use what works for your family.

In order to keep the bed looking like one piece, we opted to keep all the white sides visible.  You can also check out other hacks where the panel boards are redecorated. Complete creative freedom with this bed!

The beds were assembled so that they were mirror images.  Due to space restrictions, our ladders would be up against the walls, making them unusable, so we faced the solid side of the bed out so they could climb up that way.  If you prefer to have the entire bottom space open for easier access and airflow, simply assemble so the open side is facing out.  We suggest that the entire bed be put against a wall that will act as your headboard.


Step 2: Remove or do not install the bottom crossbar that faces the middle of the bed

If your room is large enough to fit this bar in it's new location without cutting it, do that!  If not, you can either cut it to size or replace it with a 2x4 sized piece of wood.  We opted to buy other wood and store the crossbar so that the bed could be used on it's own in the future.  These cross bars help stabilize the bed.  If you wish to put something in the space the crossbar previously occupied, we suggest something flat that a mattress will lay easily on top of.

To anchor these, we used l brackets screwed into the wood leg of the bed and the wood cross bar.


Step 3: Purchase two 2x4 pieces of wood and white panel board.

We bought the 2x4's that most closely matched the bed colors natural wood.  We did not have the time or energy to sand and stain.  It isn't exact, but you can hardly tell.  We had Home Depot cut it to fit between the two beds to create a crossbar/shelf.

Next we purchased white panel board.  You can purchase a large piece that can be cut lengthwise only and have it be one solid piece.

Finished seam looks like this...


Step 4: Nail the white board to the two 2x4's with small white panel nails to create one long piece


Step 5:  Attach the headboard to the two beds

Using corner brackets and screws we attached the headboard to each bed.  It was a perfect match, but it worked well enough!  It just needed to be secure and safe.




Once attached, it should look like this on each side...


Step 6:  Put in mattresses

We have a twin mattress on top of each bunk.  On the bottom, we are able to fit a king, twin and toddler mattress easily.  It is possible to fit two twins, but it is a very tight squeeze.  There are some small gaps around the bed.  We have taken extra body pillow and filled them in.  You could do the same.

Our mattresses are on the floor.  You could choose to take plywood and make a palette for them to sit on if you wanted.




Step 7:  Decorate!

We wanted to keep it simple and easy, but also make each space feel like it's own.  We used IKEA curtain rods and IKEA curtains to section off each space.  We purchased battery operated wire lights to put in each space for reading at bedtime.  We used a small folding travel bag from Target hung from a hook to hold phone, earplugs, nose spray and CPAP.  We hung up a few pictures and we were done!

Cost Breakdown of what we spent:
  • Kura Beds $150
  • Wood and paneling to make one bed: $16.50
  • Curtains, rods and lights for the beds (4 sets): $61.00
We actually already owned the curtains, rods, and beds, so the only cost was the wood and paneling as well as the lights.  Everything else was re-purposed from other areas of the house.


You should buy lights with a remote (shown below) since it proves hard to get the lights off if the kids fall asleep with them on.



via wanderingtheworldbelow , diycozyhome

Δημοσίευση σχολίου